Agricultural valves

Tractor valves tyre valves air water ALLIGATOR, 20x tractor tyre valvesAir/water valves (TR618A) for agriculture for safe and reliable filling of tractor tyres with water. The wide vent allows the large tyres to be filled with water in a short time, after removing the valve core housing, to improve the tractor's pulling power. Of course, water filling cannot be dispensed with the usual air filling of the tyres. The tractor tyres can be filled with water and emptied completely using the appropriate water filling fittings.Tightening torque: 5-8Nm, valve length: 50mm, valve hole Ø: 15.7 + 0.4mm

Tractor valves tyre valves for commercial vehicles ALLIGATOR,..x tractor tyre valvesAir/water valves for agriculture for safe and reliable filling of tractor tyres with water. The wide vent allows the large tyres to be filled with water in a short time, after removing the valve core housing, to improve the tractor's pulling power. Of course, water filling cannot be dispensed with the usual air filling of the tyres. The tractor tyres can be filled with water and emptied completely using the appropriate water filling fittings.

High quality air and water valve from ALLIGATOR, suitable for tractors. Delivery in a practical box of 20 pieces. Vehicle typetractorMaterialbrassStandardization ETRTOV4.02.1Standardization TRTRCH3Design of valve capround headLength of valve stem in mm35,5 mm

Rims Valve TR618A: Variant: Mounts ETRTO: V5.01.1 Valve height in mm: 50.5 Ø valve hole in mm: 15.7 packaging units: 10-piece tightening torque: 5-8.5 NmWhen should metal tyre valves be changed? The best thing is to change the tyres every time!The metal valves are subjected to enormous stress during their service life and are exposed to many different environmental influences. These include varying levels of ozone, solar radiation and the use of chemicals. It does not matter whether it is an Auto tyre valve, truck or bicycle or what material (rubber or metal) it is.Therefore, every time a tyre is changed in the workshop, not only the tyres and rims but also the valves should be inspected and tested. A safe driving experience can only be guaranteed with a regular check of the rim valves. Potential tyre pressure loss can be caused by defective metal or rubber valves. In addition, external damage to the rim valve or corrosion of the valve core can also be responsible.The consequences of tyre pressure loss include various safety risks, with increased tyre wear, increased rolling resistance and increased fuel consumption among the less dangerous ones. However, a broken metal tyre valve can have the negative effect of increasing the braking distance and can lead to unsafe driving with the risk of losing control of the vehicle.In order to minimise the safety risk and to achieve an optimal driving experience, we advise you to have the tyre valves and rim valves checked and replaced regularly.

The ALLIGATOR air / water rim valve has a hole of 15.7 + 0.4 mm and a length of 40 mm. In addition, the valve is equipped with a round head cap and has a tightening torque of 5 - 8 Nm.

Rim nut made of brass with 12V1 thread. Accessories for agricultural valves. Vehicle typetractorMaterialbrassStandardization ETRTOV9.14.1Standardization TRTRLN10

With the combined water filling and deflation device “Hanauer Maus", which is made of nickel-plated brass, tractor tyres whose air/water valves are equipped with a valve core housing can be filled with water and can also be deflated. Vehicle typetractorCoatingnickelMaterialbrassLength of valve stem in mm116 mm

The ALLIGATOR air / water rim valve has a hole of 15.7 + 0.4 mm and a length of 54 mm. In addition, the valve is equipped with a round head cap and has a tightening torque of 5 - 8 Nm.

Tyre valve for tractors: Variant: Mounts valve height in mm: 57 Ø valve hole in mm: 15.7 packaging units: 10-piece tightening torque: 5-8.5 NmHow often should rubber valves be changed?For an optimum driving experience, we recommend that you also check and change the rubber valves every time you change a tyre. The rubber valves on car tyres can be damaged by various external influences. This can lead to a potential pressure loss in the valves, which represents a high safety risk. In addition, the heavy strain also shortens the service life of the rubber valves.Therefore it is recommended to check the car rubber valves regularly. Above all, attention should be paid to whether the rubber on the valves is brittle, whether there is corrosion on the valve core or whether the tyre valve has been damaged.If a broken or defective rubber valve is not replaced, various safety risks may occur. The consequences of tyre pressure loss include increased tyre wear, higher fuel consumption and increased rolling resistance. In the most dangerous case, defective car rubber valves lead to an extended braking distance and unsafe driving behaviour, up to the loss of control over the vehicle.For your own safety, we therefore recommend that you replace the rubber valve sets. We offer a wide range of rubber valves for cars, vans, trucks, motorcycles, scooters, tractors and construction machinery. Please have a look at our tyre valves.

The ALLIGATOR air / water rim valve TR 218A has a hole of 15.7 + 0.4 mm and a length of 47 mm. In addition, the valve is equipped with a round head cap and has a tightening torque of 5 - 8 Nm. ETRTO no: V4.01.1

Plastic rim nut with 12V1 thread. Accessories for agricultural valves. Vehicle typetractorMaterialplasticStandardization ETRTOV9.14.1EQStandardization TRTRLN10

The flexible valve extension 615mm with 2 nuts from ALLIGATOR enables hard-to-reach valves to be reached and is ideal for earthmoving machines. The highly flexible hose extension made of rubber with an effective length of 596mm can withstand a pressure resistance of 70 bar. A clamp is required for assembly. The flexibility (100%) of the hose ensures a high level of break resistance and flexible use. It should be noted that valve extensions made of rubber are under pressure (up to 20 bar), should not be kinked and must not touch the rim hole. Valve extensions are not to be used together with rubber valves.

The water filling fitting made of nickel-plated brass is used as a fitting for connection to air/water valves. Vehicle typetractorCoatingnickelMaterialbrassLength of valve stem in mm33,5 mm

Tyre valve TR623A: Ø 15.7 mm ETRTO: V5.02.3 Height: 39 mm length: 54 mm angle: 115° packaging unit: 10-piece tightening torque: 5-8,5 NmWhen should metal tyre valves be changed? The best thing is to change the tyres every time!The metal valves are subjected to enormous stress during their service life and are exposed to many different environmental influences. These include varying levels of ozone, solar radiation and the use of chemicals. It does not matter whether it is an Auto tyre valve, truck or bicycle or what material (rubber or metal) it is.Therefore, every time a tyre is changed in the workshop, not only the tyres and rims but also the valves should be inspected and tested. A safe driving experience can only be guaranteed with a regular check of the rim valves. Potential tyre pressure loss can be caused by defective metal or rubber valves. In addition, external damage to the rim valve or corrosion of the valve core can also be responsible.The consequences of tyre pressure loss include various safety risks, with increased tyre wear, increased rolling resistance and increased fuel consumption among the less dangerous ones. However, a broken metal tyre valve can have the negative effect of increasing the braking distance and can lead to unsafe driving with the risk of losing control of the vehicle.In order to minimise the safety risk and to achieve an optimal driving experience, we advise you to have the tyre valves and rim valves checked and replaced regularly.

With the combined water filling and deflation device "Waterboy", which is made of nickel-plated brass, tractor tyres whose air/water valves are equipped with a valve core housing can be filled with water and can also be deflated. Vehicle typetractorCoatingnickelMaterialbrassLength of valve stem in mm98,5 mm

The ALLIGATOR air / water rim valve TR 623A has a bending angle of 65 °, a hole of 15.7 + 0.4 mm and a length of 57 mm. In addition, the valve is equipped with a round head cap and has a tightening torque of 5 - 8 Nm. ETRTO no: V5.02.3

The ALLIGATOR air / water rim valve TR 621A has a bending angle of 65 °, a hole of 15.7 + 0.4 mm and a length of 75 mm. In addition, the valve is equipped with a round head cap and has a tightening torque of 5 - 8 Nm. ETRTO no: V5.02.1

You will receive the high quality ALLIGATOR air / water rim valve with a bending angle of 90 °.